A dual-band ExpressLRS TX module that can transmit 2.4 GHz and 915 MHz at the same time, with up to 1000mW output, XT30 2–6S external power, active fan cooling and WiFi + Bluetooth setup. Available for full-size JR bays and Nano bays.
Two bands. One link.Pair it with the Aeris Link Dual Band Receiver (dual antenna) for X-Band: every packet rides both bands, so if one is blocked the other keeps you in control.
RF output1000mWDual output, adjustable
Bands2.4 / 915GHz / MHz · Semtech LR1121
External powerXT30DC 5–26 V (2–6S)
WirelessWiFi + BTSetup and updates, no cables
01 / The Link
Both bands. Same packet. Same time.
Most links make you choose: 2.4 GHz for crisp control or 915 MHz to punch through trees and terrain. In X-Band mode, Aeris Link Dual sends the same packet on both bands in parallel. If one band gets jammed or blocked, the other is still carrying your sticks.
2.4 GHzHigh packet rates and sharp response for freestyle, racing and crowded fields.
915 MHzBetter penetration and diffraction for long range and obstructed spots.
X-BandOne antenna per band, both carrying the same packet, so one band backs up the other.
Redundancy, honestlyGemini and X-Band steady your link quality; they do not add range. For reach, use 915 MHz, more power and good antenna placement.
Select modes in the ExpressLRS Lua script on your radio. Gemini sends the same packet on two frequencies to a true-diversity receiver. DK500 on 2.4 GHz sends each packet twice at 500 Hz for fewer drops when many pilots share the air. X-Band needs dual-radio, dual-band hardware at both ends: this module plus the Aeris Link Dual Band Receiver (dual antenna).
03 / Power On Your Terms
Up to 1000mW, from bench tuning to long-range cruising.
Output is adjustable across seven levels. For high output, plug a 2–6S pack into the XT30 port. Always fit both antennas before powering on.
Adjustable output10 / 25 / 50 / 100 / 250 / 500 / 1000 mW, set from the Lua script.
XT30 external powerDC 5–26 V (2–6S), so high-output flying does not rely solely on your radio bay power.
Low for practiceRun low power for daily practice, indoor tuning and the field next door.
High for rangeTurn it up when you head out past the treeline.
04 / Built To Run Cool
Active cooling and every port where you need it.
Central fan + aluminum shellAir intake and exhaust paths move air through the heat-sink housing for active cooling at high output.
PortsXT30 power input, USB Type-C for firmware flashing, and two SMA antenna ports with dual-band T antennas included.
RGB status LEDLink state visible at a glance.
05 / Wireless & Smart
Set it up from your phone.
Dual-MCU designESP32-PICO-D4 runs the link; an onboard ESP32-C3 handles ExpressLRS Backpack.
WiFi + BluetoothChange settings and update firmware without a cable.
CRSF + LuaWorks with CRSF-capable OpenTX / EdgeTX radios and the ExpressLRS Lua script.
Firmware targetEMAX LR1121.
06 / Choose Your Bay
Full-size or compact. Same dual-band link.
Full-size JR bay module
Nano bay module
Radio interface
Standard 5-pin JR bay
Standard 8-pin Nano bay
Fits
Full-size radios with a JR module bay
Compact radios with a Nano module bay
Size (excl. antennas)
≈ 81 × 55 × 40 mm
≈ 80 × 39 × 24 mm
Weight (excl. antennas)
≈ 70 g
≈ 61 g
Mounting
Quick-release installation latch
Standard Nano bay fit
Both versions share the same RF, MCUs, cooling, power input and features.
07 / Complete The System
Unlock X-Band with the dual-antenna receiver.
Paired with
2.4 GHz
915 MHz
Gemini / diversity
X-Band
Aeris Link Dual Band RX · Dual antenna
Yes
Yes
Yes
Yes
Aeris Link Dual Band RX · Single antenna
Yes, one band at a time
Yes, one band at a time
No
No
Receivers sold separately. With other ExpressLRS receivers, use a matching ELRS major version and a shared packet rate.
08 / Specifications
Full specs.
Radio interface
Standard 5-pin JR bay / standard 8-pin Nano bay
Main MCU
ESP32-PICO-D4
Aux MCU
ESP32-C3 (Backpack)
RF
Semtech LR1121
RF bands
ISM 2.4 GHz / FCC 915 MHz
Frequency range
2400–2480 MHz / 860–960 MHz
RF power
Dual output, up to 1000 mW (10 / 25 / 50 / 100 / 250 / 500 / 1000 mW). See the Output Power Note below.
Do I need a dual-band receiver?For X-Band, yes: pair the module with the Aeris Link Dual Band Receiver (dual antenna). The single-antenna receiver and other ExpressLRS receivers run one band at a time.
Do Gemini or X-Band increase range?No. They send the same packet on two frequencies or two bands for redundancy and steadier link quality.
Should I use external power?At high output, yes. Plug a 2–6S pack into the XT30 port (DC 5–26 V).
Which version fits my radio?Check the module bay on the back of your radio: a standard 5-pin JR bay takes the full-size module; an 8-pin Nano bay takes the Nano module.
Anything to know before first power-up?Always fit both antennas before powering on, because running without antennas can damage the RF amplifier. Set the correct regulatory domain for your region (FCC 915 MHz or EU 868 MHz) and match ExpressLRS versions and binding phrase.
Output Power Note
Shipping firmware is limited to 500mW. New Chinese export rules on drone radio equipment took effect in November 2026. To comply, current production batches of the Aeris Link Dual TX ship with firmware capped at 500mW output, with a low factory default power.
The hardware is built for 1000mW. EMAX is releasing a firmware update and flashing guide that unlocks the module's full 1000mW output. Watch emaxmodel.com for the update, and always fly within your local radio regulations.
Specifications are from EMAX product documentation. ExpressLRS features depend on firmware version and receiver support.