ExpressLRS receivers built on the Semtech LR1121. Run 2.4 GHz for crisp, high-rate response or 915 MHz to punch through trees and obstacles. Choose the dual-antenna RX for true diversity, Gemini and X-Band, or the 0.85 g single-antenna RX that switches between bands.
If one band drops, the other keeps flying.Pair the dual-antenna RX with the Aeris Link Dual TX and X-Band sends every packet on 2.4 GHz and 915 MHz at the same time.
Dual antenna RX1.35 gLR1121 ×2 · 20 × 16 × 3 mm
Single antenna RX0.85 gLR1121 · 18 × 11 × 3 mm
Bands2.4 / 915GHz / MHz (868 MHz EU)
Telemetry100 mW10 / 25 / 50 / 100 mW
01 / The Link
Two radios on one tiny board.
The dual-antenna receiver carries two LR1121 RF chips, each with its own antenna. In X-Band mode with the Aeris Link Dual TX, the same control packet is sent on 2.4 GHz and 915 MHz in parallel. A tree line, a concrete pillar or a noisy channel can take out one band while the other still delivers.
Mode
Band
What it does
Works with
2.4 GHz True Diversity
2.4 GHz
Two complete RF paths listen at once; the stronger signal wins in real time
2.4 GHz ExpressLRS TX
2.4 GHz Gemini
2.4 GHz
Same packet on two 2.4 GHz frequencies in parallel
Aeris Link Dual TX, Mode 1
915 MHz True Diversity
915 MHz
Two RF paths on 915 MHz; picks the better signal
915 MHz ExpressLRS TX
915 MHz Gemini
915 MHz
Same packet on two 915 MHz frequencies in parallel
Aeris Link Dual TX, Mode 2
X-Band (Gemini Xrossband)
2.4 GHz + 915 MHz
Same packet on both bands at once. If one band is jammed or blocked, the other carries it
Aeris Link Dual TX, Mode 3
Receive modes apply to the dual-antenna receiver. Gemini and X-Band add redundancy and steadier link quality, not extra range. Range still depends on band, packet rate, output power and antennas.
02 / Which One Is Right For You
Dual antenna for maximum redundancy. Single antenna for every gram.
Both receivers cover 2.4 GHz and 915 MHz on the LR1121. They differ in how many links run at once and how much weight you can spare.
Dual antenna receiver
Single antenna receiver
RF chip
LR1121 ×2
LR1121 ×1
Antennas
2 × dual-band T antenna (IPEX1)
1 × dual-band T antenna (IPEX1)
Bands
2.4 GHz and 915 MHz; both at once in X-Band (Aeris Link Dual TX)
2.4 GHz or 915 MHz, switchable
Receive modes
True diversity, Gemini (2.4 / 915), X-Band
One band at a time
Weight
1.35 g
0.85 g
Size
20 × 16 × 3 mm
18 × 11 × 3 mm
Suggested builds
5-inch freestyle, long range, high-RF-noise spots
Whoops, micros and light builds
03 / Pick Your Band
2.4 GHz to rip. 915 MHz to roam.
Each band has a job. The single-antenna RX lets you switch between them to suit the spot; the dual-antenna RX can run both together.
2.4 GHzHigh packet rates and a crisp stick feel for freestyle, racing and fields packed with pilots.
915 MHzBetter penetration and diffraction around trees, buildings and terrain for long-range cruising.
X-BandBoth bands at once on the dual-antenna RX with the Aeris Link Dual TX, so one band backs up the other.
DK500 on 2.4 GHzSends each packet twice at 500 Hz for fast response and fewer lost packets when many pilots fly together.
Packet rates follow your ExpressLRS transmitter. With the Aeris Link Dual TX: 2.4 GHz 50–500 Hz including DK250 / DK500, 915 MHz D50–250 Hz including Full-resolution rates, X-Band 100 Hz Full / 150 Hz.
04 / Field-Ready Details
Small board. Serious link hardware.
Built-in TCXOA temperature-compensated crystal oscillator corrects frequency drift, keeping the link stable from cold mornings to hot afternoons.
Full-state RGB LEDA different color per band tells 2.4 GHz from 915 MHz at a glance. The pattern follows packet rate and flags abnormal states without plugging in.
Up to 100 mW telemetryFour levels (10 / 25 / 50 / 100 mW) keep link stats and your flight controller telemetry coming back.
WiFi web UIUpdate firmware and change settings from your phone or laptop over WiFi.
CRSF and SBUSStandard serial output for modern flight controllers.
Antennas includedDual-band T antennas in the box: two with the dual RX, one with the single RX.
05 / Install
Four wires, one antenna plug.
Wire itRun the included 100 mm 4-pin cable to a free UART: 5 V, GND, receiver TX to FC RX, receiver RX to FC TX.
Set itEnable Serial RX on that UART and select CRSF in your flight controller configurator.
Bind itMatch the ExpressLRS major version and binding phrase on TX and RX. Use the FCC 915 MHz domain in FCC regions and 868 MHz in EU regions.
Mount itOn the dual RX, place the two antennas as far apart as you can, at different angles, away from carbon, the battery and the VTX.
06 / Compatibility
Works with ExpressLRS today. Unlocks X-Band with Aeris Link Dual.
Your transmitter
Dual antenna RX
Single antenna RX
Aeris Link Dual TX (JR or Nano bay)
All five modes, including X-Band
2.4 GHz or 915 MHz, one band at a time (TX in Mode 1 or 2)
Other 2.4 GHz ExpressLRS TX
2.4 GHz true diversity
2.4 GHz
Other 915 MHz ExpressLRS TX
915 MHz true diversity
915 MHz
Requires a matching ExpressLRS major version and a packet rate both ends support. LR1121-only rates such as DK250 / DK500 need an LR1121 transmitter. A single-antenna receiver will not sync in X-Band mode.
Transmitter sold separately. For X-Band, pair the dual-antenna receiver with the Aeris Link Dual ExpressLRS TX.
09 / FAQ
Quick answers.
Do I need the Aeris Link Dual TX?Only for Gemini and X-Band. Both receivers also run as standard ExpressLRS receivers with a 2.4 GHz or 915 MHz ExpressLRS transmitter on that band.
Do Gemini or X-Band add range?No. They send the same packet two ways for redundancy, so link quality stays steadier and a blocked band or noisy channel is far less likely to drop you.
Can the single-antenna RX do Gemini or X-Band?No. It has one LR1121 and one antenna, so it runs one band at a time: 2.4 GHz or 915 MHz. Choose the dual-antenna RX for diversity, Gemini and X-Band.
915 MHz or 868 MHz?Use the FCC 915 MHz domain in FCC regions; 868 MHz is the EU setting. Keep transmitter and receiver on the same regulatory domain.
How do I update firmware?Over WiFi: start the receiver in WiFi mode and open the ExpressLRS web UI from your phone or laptop.
Specifications are from EMAX product documentation. ExpressLRS features depend on firmware version and transmitter support.